Electric Linear Slides EZS Series
EZS6L-E010-ARMCD-2
Actuator/Control Circuit
| Classificazione prodotto | Nome del prodotto | Prezzo di listino | Data di spedizione |
|---|---|---|---|
| Actuator / Control Circuit | EZS6L-E010-ARMCD-2 | - | Prodotto fuori produzione (31.3.2025 fuori produzione) |
Incluso
- Actuator, Circuit, Cable for motor (2 m), Cable for Electromagnetic Brake (2 m), I/O Signal Connector, Sensor Signal Connector, Connector for Regeneration Resistor Input/Main Power Input Terminals, 24 VDC Power Supply Input/Regeneration Resistor Thermal Input/Electromagnetic Brake Output Terminal, Connector Wiring Lever
Specifiche
Caratteristiche
Operating Speed - Load Mass
About this vertical drive
Dimensioni
Actuator
Scarica i dati
Altre Specifiche
General Specifications
AC Input
| Motor Section (AR Series) | Driver | |||
|---|---|---|---|---|
| Built-In Controller Type | Pulse input type | |||
| Thermal Class | 130 (B) | − | ||
| Insulation Resistance |
100 MΩ or more when 500 VDC megger is applied between the following places.
|
100 MΩ or more when 500 VDC megger is applied between the following places.
|
||
| Dielectric Strength |
Sufficient to withstand the following for 1 minute:
|
Sufficient to withstand the following for 1 minute: | ||
|
|
|||
| Operating Environment (When operating) |
Ambient Temperature | 0~+50 °C (Non-freezing)*2 | 0~+55 °C (Non-freezing)*3 | 0~+50 °C (Non-freezing)*3 |
| Ambient Humidity | 85 % max. (Non-condensing) | |||
| Atmosphere | No corrosive gases or dust. No exposure to water, oil or other liquids. | |||
| Degree of Protection | IP65 (Motor section only. Except for the connector) | IP10 | IP20 | |
- *1
- (Only for types with electromagnetic brake)
- *2
- The temperature range of the electric linear slide is 0~+40 °C.
- *3
- When installing a heat sink equivalent to an aluminum plate min. 200×200 mm, thickness 2 mm
Note
- Do not perform the insulation resistance test or the dielectric strength test while the electric linear slides (motors) and drivers are connected.
DC Input
| Motor Section (AR Series) | Driver | |||
|---|---|---|---|---|
| Built-In Controller Type | Pulse input type | |||
| Thermal Class | 130 (B) [Certified at 105 (A) when UL/CSA Standards were obtained] |
− | ||
| Insulation Resistance |
100 MΩ or more when 500 VDC megger is applied between the following places.
|
100 MΩ or more when 500 VDC megger is applied between the following places.
|
- | |
| Dielectric Strength |
Sufficient to withstand the following for 1 minute:
|
Sufficient to withstand the following for 1 minute:
|
- | |
| Operating Environment (When operating) |
Ambient Temperature | 0~+50 °C (Non-freezing)*2 | 0~+50 °C (Non-freezing) | |
| Ambient Humidity | 85 % max. (Non-condensing) | |||
| Atmosphere | No corrosive gases or dust. No exposure to water, oil or other liquids. | |||
| Degree of Protection | IP20 (motor section only) | IP10 | IP20 | |
- *1
- (Only for types with electromagnetic brake)
- *2
- The temperature range of the electric linear slide is 0~+40 °C.
Note
- Do not perform the insulation resistance test or the dielectric strength test while the electric linear slides (motors) and drivers are connected.
Driver Circuit Specifications
| Built-In Controller Type | Pulse Input Type | ||
|---|---|---|---|
| Maximum Input Pulse Frequency | − | Line Driver Output by Host Controller: 500 kHz (at 50 % duty) Open-Collector Output by Host Controller: 250 kHz (at 50 % duty)*1 Negative logic pulse input (initial value) |
|
| Number of Positioning Data Sets | 64 Points | − | |
| Positioning Operation | Independent | ◯ | − |
| Linked | ◯ | − | |
| Linked 2 | ◯ | − | |
| Sequential | ◯ | − | |
| Direct | ◯ | − | |
| Pushing | ◯ | ◯*2 | |
| Continuous Operation | ◯ | − | |
| JOG Operation | ◯ | − | |
| Return-To-Home Operation | ◯ | − | |
| Test Operation | ◯ | ◯*2 | |
| Absolute-position backup system | ◯ | − | |
| Control Module OPX-2A | ◯ | ◯ | |
| Support Software MEXE02 | ◯ | ◯ | |
- *1
- The value when the general-purpose cable (CC36D1E) (sold separately) is used.
- *2
- Setting by extended function (MEXE02)
RS-485 Communication Specifications
| Protocol | Modbus RTU mode |
|---|---|
| Electrical Characteristics | EIA-485 Compliant, straight cable Use twisted-pair cables (TIA/EIA-568B CAT5e or better recommended), the max. total extension length is 50 m.* |
| Mode | Half duplex and asynchronous mode (data: 8 bits, stop bit: 1 bit or 2 bits, parity: none, even, or odd) |
| Transmission Rate | Selectable from 9,600 bps, 19,200 bps, 38,400 bps, 57,600 bps and 115,200 bps. |
| Connection Type | Up to 31 drivers can be connected to one host controller. |
- *If a specific wiring and layout causes the motor cable or power supply cable to generate a noise problem, shield the cable or use ferrite cores.
Standard
Regulations and Standards Materials
Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)
Explanations of the Global Laws, Regulations and Standards can be found here.
Information about our compliance with regulations and standards for each of our product series can be found here.
Hazardous Substances
The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).
For more information about compliance with regulations on chemical substances in Oriental Motor's Products, click here.
Configurazione del sistema
Prodotti correlati
| Products | Features | ||
|---|---|---|---|
NETC02-CC
|
Features |
[CC-Link Ver. 2 Compatible] By supporting CC-Link Ver.2, you can simplify the ladder program and shorten the communication time for data sending and receiving. |
|
| Products |
NETC01-ECT
|
Features |
[EtherCAT Compatible] |