AC Speed Control Motors V Series

VSR590C-60J

Stampa tutte le informazioni sul prodotto in una volta sola
VSR590C-60J

Combi geared motor
  Questo prodotto non è più disponibile per la vendita.
Classificazione prodotto Nome del prodotto Prezzo di listino Data di spedizione
Combi geared motor VSR590C-60J - Prodotto fuori produzione
(31.3.2019 fuori produzione)
• Circuit required separately.

Incluso

  • Motor, Gearhead, Capacitor, Capacitor Cap, Installation Screws, Parallel Key, Operating Manual

Specifiche

Scarica i dati

Altre Specifiche

General Specifications

Item Specifications
Insulation Resistance After rated operation at normal ambient temperature and humidity, the measurement between the coils and the case is 100 MΩ min. using a 500 VDC megger.
Dielectric Strength No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after rated operation at normal ambient temperature and humidity.
Temperature Rise After no-load rated operation at normal ambient temperature and humidity, the winding temperature rise measured by the resistance change method is 80 °C max.
Overheat Protective Device The 6 W type is impedance protected.
All other motors have a built-in thermal protector (automatic reset type)
Open...130±5℃ Reset...82±15℃
Operating Ambient Temperature 110/115 V, 220/230 V: -10~+40°C (Non-freezing)
100 V, 200 V: -10~+50°C (Non-freezing)
Operating Ambient Humidity 85 % max. (Non-condensing)
Thermal Class 130(B)
Degree of Protection IP20

Control Circuit Specifications

Speed Controller Product Name MSC-1
Power Supply Voltage Single-Phase 100/110/115 VAC±10%
Single-Phase 200/220/230 VAC±10%
Power Supply Frequency 50/60 Hz
Applicable Speed Controls
Motor Output Power		 6 W, 15 W, 25 W, 40 W, 60 W, 90 W
Variable Speed Range 50Hz: 90~1400r/min
60Hz: 90~1600r/min
Functions Speed control, no-contact instantaneous stop, no-contact bidirectional rotation, no-contact rotation speed switching,
slow start/slow down (0.3~15 sec. at 1000 r/min with no load)
Speed Setting Methods

Set the speed in the following way.

  • Internal Speed Potentiometer
  • External Speed Potentiometer: Accessory (sold separately): PAVR-20KZ（20kΩ, 1/4W）
  • External DC Voltage: 0~5 VDC or 0~10 VDC switching, 1 mA min.
Control Power Supply 24 VDC±10 % min. 100 mA
Input Signals Photocoupler Input 　Input Resistance: 4.7 kΩ
FWD, REV, INT/EXT, ALARM-RESET
Output Signals Open-collector output max. 30 VDC
SPEED-OUT: max. 10 mA, ALARM-OUT: max. 40 mA
Protective Functions

When the following protective functions are activated, the motor will coast to a stop, and the ALARM output will be turned off.
The LED of the speed controller blinks the number of times in parentheses.

  • Motor Lock (2 times): When the motor output shaft is restrained for 5 seconds min., or when the tachogenerator wire is disconnected or poorly connected
  • Motor Overheat (9 times): When the motor's built-in thermal protector operates (OPEN)., when the motor wire is disconnected or poorly connected
Insulation Resistance After continuous operation at normal ambient temperature and humidity, the measurement value between the main circuit terminal and the control circuit terminal or the main circuit terminal and the case is 100 MΩ min. using a 500 VDC megger.
Dielectric Strength After continuous operation at normal ambient temperature and humidity, no abnormality is observed when 1.9 kVAC at 50 Hz or 60 Hz is applied between the main circuit terminals and the control circuit terminals, or between the main circuit terminals and the case for 1 minute.
Operating Ambient Temperature 0~+50°C (Non-freezing)
Operating Ambient Humidity 85 % max. (Non-condensing)
Degree of Protection IP10

Note

  • Vertical operation (gravitational operation) is not possible.

Permissible Radial Load and Permissible Axial Load of Gearhead

Product Name Gear Ratio Maximum Permissible Torque
N·m		 Permissible Radial Load N Permissible Axial Load
N
From Shaft End
10 mm		 From Shaft End
20 mm
GV2G□ 5~9 6.0 100 150 40
12.5~25 150 200
30~360 200 300
GV3G□ 5~9 10 150 200 80
12.5~25 200 300
30~360 300 400
GV4G□ 5~9 16 200 250 100
12.5~25 300 350
30~360 450 550
GVH5G□ 5~9 30 400 500 150
12.5~18 450 600
25~300 500 700
GVR5G□ 5~9 40 400 500 150
12.5~18 450 600
25~180 500 700
Radial Load and Axial Load
Scarica i dati
Stampa tutte le informazioni sul prodotto in una volta sola
close
close