AC Speed Control Motors US2 Series
US2-590JC-GAR100-1N
Motor/Control Circuit
Questo prodotto non è più disponibile per la vendita.
| Classificazione prodotto | Nome del prodotto | Prezzo di listino | Data di spedizione |
|---|---|---|---|
| Geared Motor / Control Circuit | US2-590JC-GAR100-1N | - | Prodotto fuori produzione (31.3.2021 fuori produzione) |
Incluso
- Geared Motor, Control Circuit, Mounting Screws, Parallel Key, Connection Cable (1 m)
Specifiche
Dimensioni
Scarica i dati
Altre Specifiche
Common Specifications
| Item | Specifications | |
|---|---|---|
| Speed Setting Methods |
Digital setting with dial (speed setting is available by units of 1 r/min) |
|
| Variable Speed Range |
50 Hz: 90~1400 r/min 60 Hz: 90~1600 r/min |
|
| Acceleration Time and Deceleration Time | 0.1~15.0 seconds (Initial Setting: 1.0 second) Acceleration time/deceleration time varies with the load condition of the motor. |
|
| Function | Parameters | Gear ratio, speed increasing ratio, fixed last digit display, prevention of operation at power-on alarm, speed upper/lower limit, acceleration/deceleration time, external operation signal input, data initialization |
| Monitor | Rotation speed, input signal | |
| Other | Lock data editing | |
| Input Signals | Photocoupler Input Input resistance: 2 kΩ FWD Input, REV Input 2 points |
|
| Protective Function | The motor will make a coasting stop and the alarm code will be displayed on the operation panel when the following protective functions are activated. Alarm Types: Motor overheat, Motor lock, poor motor connection, EEPROM error, prevention of operation at power-on |
|
| Maximum Extension Distance | Between motor and speed controller 10 m | |
General Specifications
| Item | Motor | Speed Controller | |
|---|---|---|---|
| Insulation Resistance | 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. | Measurement value of 100 MΩ min. when a 500 VDC megger is applied between the main circuit terminal and the input signal terminal, between the main circuit terminal and the case, and between the main circuit terminal and FG after continuous operation under normal ambient temperature and humidity. | |
| Dielectric Strength | No abnormality is observed when 1.5 kVAC at 50 Hz or 60 Hz applied between the coils and case for 1 minute after continuous operation under normal ambient temperature and humidity. | No abnormality is observed when 1.9 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and the input signal terminal and between the main circuit terminal and the case, and 1.5 kVAC at 50 Hz or 60 Hz applied between the main circuit terminal and FG for 1 minute after continuous operation under normal ambient temperature and humidity. | |
| Temperature Rise | Winding temperature rise value is 80 °C max. measured by the resistance change method after no load continuous operation under normal ambient temperature and humidity. | - | |
| Overheat Protective Device | Built-in Thermal Protector (Automatic Return Type) Open: 130±5 ℃, Reset: 85±20 ℃ |
- | |
| Operating Environment | Ambient Temperature | 0~+50 °C (Non-freezing) | |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Up to 1000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | ||
| Vibration | Not subject to continuous vibration or excessive shock In conformance with JIS C 60068-2-6, "Sine-wave vibration test method" Frequency Range: 10∼55 Hz, Half Amplitude: 0.15 mm, Sweep Direction: 3 directions (X, Y, Z), Number of Sweeps: 20 times |
||
| Storage Conditions* | Ambient Temperature | -25~+70°C (Non-freezing) | -25~+70°C (Non-freezing) |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Up to 3000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | ||
| Thermal Class | 130(B) | - | |
| Degree of Protection | IP20 | IP20 | |
- *The value for storage condition applies to short periods such as the period during transport.
Note
- Do not measure insulation resistance or perform a dielectric strength test while the motor and speed controller are connected.
Permissible Radial Load and Permissible Axial Load
| Gear Ratio | 5 | 7.5 | 10 | 15 | 20 | 25 | 30 | 40 | 50 | 60 | 75 | 100 | 120 | 150 | 200 | 240 | ||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Permissible Radial Load [N] |
Hollow Shaft* | 10 mm From Mounting Surface | 1200 |
2200 |
||||||||||||||
| 20 mm From Mounting Surface | 1100 |
2000 |
||||||||||||||||
| Solid Shaft | 10 mm From the End of the Output Shaft | 900 |
1700 | |||||||||||||||
| 20 mm From the End of the Output Shaft | 1000 |
1850 | ||||||||||||||||
| Permissible Axial Load [N] | 350 | |||||||||||||||||
Standard
Regulations and Standards Materials
Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)
Explanations of the Global Laws, Regulations and Standards can be found here.
Information about our compliance with safety standards for each of our product models can be found here.
Hazardous Substances
The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).
For more information about compliance with regulations on chemical substances in Oriental Motor's Products, click here.
Configurazione del sistema
Cavi e accessori
close
close