Brushless Motors HBL Series

HBL560N-50

Stampa tutte le informazioni sul prodotto in una volta sola
HBL560N-50

Gearhead / Motor / Control Circuit

  Questo prodotto non è più disponibile per la vendita.
Classificazione prodotto Nome del prodotto Prezzo di listino Data di spedizione
Gearhead / Motor / Control Circuit HBL560N-50 - Prodotto fuori produzione
(1.4.2014 fuori produzione)

Incluso

  • Motor, Control Circuit, I/O Signals Cable with Connectors, With ConnectorPower Supply Cable, Mounting Screw Set, Operating Manual

Specifiche

Altre Specifiche

Common Specifications

Item Specifications
Speed Setting Methods Set 1 method from the following.
  • Setting by the Internal Speed Potentiometer
  • Setting by External Speed Potentiometer: accessory (sold separately): PAVR-20KZ（20kΩ, 1/4W）
  • Setting by External Dc Voltage: 0~5 VDC, 1 mA min. (input impedance 47 kΩ)
Multi-Speed Setting Methods 2-Speed
1-Speed by Internal Speed Potentiometer (1 pc) and 1-Speed by External Speed Potentiometer (accessory PAVR-20KZ) or external DC voltage (0-5VDC)
Input Signals C-MOS Negative Logic Input Method Operated by Internal Power Supply
Common to start/stop input, run/brake input, rotation direction switching input, and speed setting mode selection input
Output Signals Open-collector output Operated by external power supply Operating conditions 26.4 VDC 10 mA max.　
Common to alarm output and speed output
Protective Functions* When the following protective functions are activated, an alarm signal will be output, and the motor will come to a stop.
  • Overload Protective Function:
    When a load exceeding the rated torque is applied to the motor for about 5 seconds min.
  • Out-of-Phase Protective Function:
    When there is an abnormality in the feedback signal from the motor, such as a cable disconnection
Maximum Extension Distance Motor and driver distance: 5 m (when an accessory connection cable is used)
Time Rating Continuous
  • *The HBL series cannot control the speed control of the motor in applications where the motor side is turned from the load side, such as gravitational operation.

When a load exceeding the permissible load inertia value is driven, or when gravitational operation is performed, the overvoltage protective function works to bring the motor to a coasting stop.

General Specifications

Item Motor Driver
Insulation Resistance 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply input and the heat sink is min. 100 MΩ.
Dielectric Strength No abnormality is observed even with an application of 0.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity. After continuous operation at normal ambient temperature and humidity, no abnormality is observed when 50 Hz, 0.5 kVAC is applied between the power supply input and the heat sink for 1 minute.
Operating Environment Ambient Temperature 0∼+50°C (Non-freezing)
Ambient Humidity 85% maximum (Non-condensing)
Atmosphere No corrosive gases or dust
Thermal Class 120 (E) −

Permissible Radial Load and Permissible Axial Load

Gearhead

Product Name Gear Ratio Permissible Radial Load N Permissible Axial Load
N
10 mm From Shaft End 20 mm From Shaft End
HBL560N-□
HBL5100N-□		 5 300 400 150
10, 15, 20 400 500
30, 50, 100, 200 500 650

Round Shaft Type

Product Name Permissible Radial Load N Permissible Axial Load
10 mm From Shaft End 20 mm From Shaft End
HBL560N-A 130 150 Half of the motor mass or less
HBL5100N-A 160 170
Radial Load and Axial Load
Stampa tutte le informazioni sul prodotto in una volta sola
close