Electric Linear Slides EZS Series

EZS4R-D020-AZAAD

Actuator/Control Circuit

Dieses Produkt ist derzeit nicht mehr zum Verkauf verfügbar.

Produktklassifikation	Produktname	Preis	Versand
Actuator / Control Circuit	EZS4R-D020-AZAAD	-	Eingestelltes Produkt (Produktionsende 31.3.2023)

Inklusive

Actuator, Control Circuit, Main Power Supply/Regeneration Resistor Connector (CN4), I/O Signal Connector (CN5), Connector for 24 VDC Power Supply input · Electromagnetic Brake Connector · Regeneration Unit Thermal Input · power removal signal input (CN1), Connector Wiring Lever

Spezifikationen

Kennlinien

Operating Speed - Load Mass

Abmessungen

Actuator

Control Circuit

Weitere Spezifikationen

General Specifications (Motor)

Item		AC Input	DC Input
Thermal Class		130(B) [UL/CSA is certified at 105 (A).]
Insulation Resistance		100 MΩ or more when a 500 VDC megger is applied between the following places: Between case and motor windings Between case and electromagnetic brake windings^*1
Dielectric Strength		Sufficient to withstand the following for 1 minute. Between case and motor windings 1.5 kVAC, 50 Hz or 60 Hz Between case and electromagnetic brake windings^*1 1.5 kVAC, 50 Hz or 60 Hz	Sufficient to withstand the following for 1 minute. Between case and motor windings 1.0 kVAC, 50 Hz or 60 Hz Between case and electromagnetic brake windings^*1 1.0 kVAC, 50 Hz or 60 Hz
Operating Environment (When operating)	Ambient Temperature	0~+40 °C (Non-freezing)^*3
	Ambient Humidity	85 % max. (Non-condensing)
	Atmosphere	No corrosive gases or dust. No exposure to water, oil or other liquids.
Degree of Protection^*2		IP66 (Except for mounting surface and connector parts)
Multi-rotation detection range in a de-energized state		± 900 revolutions (1800 revolutions)

*1: (Only for types with electromagnetic brake)
*2: Motor only. The degree of protection of the electric linear slide is IP20.
*3: According to Oriental Motor’s measurement conditions.

Note

Disconnect the motor and driver when measuring insulation resistance, or conducting a dielectric strength test.
Also, do not perform these tests on the ABZO sensor part of the motor.

Driver Circuit Specifications

Classification	Name		Built-In Controller Type	Pulse input Type
I/O Function	Pulse Input		−	Maximum Input Pulse Frequency: Line driver output from host controller: 1 MHz (at 50 % duty) Open-Collector Output by Host Controller: 250 kHz (at 50 % duty) Negative Logic Pulse Input (Initial value)
	Direct Input		Input Points: 10 points	Input Points: 6 points
	Direct Output		Output Points: 6 points
	RS-485 Communication	Network Input	16 points	−
	RS-485 Communication	Network Output	16 points	−

Driver Circuit General Specifications

		Built-in Controller Type	Pulse input type
Insulation Resistance		100 MΩ or more when a 500 VDC megger is applied between the following places. Between protective earth terminal and power supply terminal Between encoder connector and power supply terminal Between I/O signal terminal and power supply terminal
Dielectric Strength		Sufficient to withstand the following for 1 minute: Between protective earth terminal and power supply terminal 1.5 kV AC, 50 Hz or 60 Hz Between encoder connector and power supply terminal 1.8 kV AC, 50 Hz or 60 Hz Between I/O signal terminal and power supply terminal 1.8 kV AC, 50 Hz or 60 Hz
Operating Environment (When operating)	Ambient Temperature	0~+55 °C (Non-freezing)^*
	Ambient Humidity	85 % max. (Non-condensing)
	Atmosphere	No corrosive gases or dust. No exposure to water, oil or other liquids.
Degree of Protection		IP10	IP20
Multi-Rotation Detection Range in Power OFF State		± 900 revolutions (1800 revolutions)

*When installing a heat sink equivalent to an aluminum plate min. 200×200 mm, thickness 2 mm

Note

Disconnect the motor and driver when measuring insulation resistance or conducting a dielectric strength test.

RS-485 Communication Specifications

Protocol	Modbus RTU Mode
Electrical Characteristics	EIA-485 Compliant, Straight Cable Use twisted-pair cables (TIA/EIA-568B CAT5e or better recommended). The max. total extension length is 50 m.^*
Mode	Half duplex communication and asynchronous mode (data: 8 bits, stop bit: 1 bit or 2 bits, parity: none, even, or odd)
Transmission Rate	9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, and 230400 bps are available.
Connection Type	Up to 31 units can be connected to a single programmable controller (master device).

*If a specific wiring and layout causes the motor cable or power supply cable to generate a noise problem, shield the cable or use ferrite cores.

Travel Direction

At the time of shipment, the travel direction of the table is set as follows.

Motor Mounting: Straight Type Motor Mounting: Reversed Motor Type

Standards

Regulations and Standards Materials

Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)

Explanations of the Global Laws, Regulations and Standards can be found here.

Information about our compliance with regulations and standards for each of our product series can be found here.

Hazardous Substances

The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).

For more information about compliance with regulations on chemical substances in Oriental Motor's Products, click here.

Systemkonfiguration

System Configuration

Produktinformationen gesammelt ausdrucken

NORTH AMERICA

EUROPE

ASIA