ORIENTAL MOTOR CO., LTD.

Inverters BHF Series

BHF62AT-100

Print Product Information All at once
BHF62AT-100

Gearhead / Motor / Control Circuit

  This product is currently no longer available for sale.
Product Classification Product Name List Price Shipping Date
Gearhead / Motor / Control Circuit BHF62AT-100 - Discontinued Product
(31.3.2019 discontinued)

Included

  • Motor, Control Circuit, Gearhead, Mounting Bracket for Control Circuit (with Screws), Mounting Screws, Parallel Key, Operating Manual

Specifications

Data Download

Other Specifications

Common Specifications

Item Specifications
Slow Start/
Slow Down		 Approx. 0.1~25 seconds (at 1000 r/min)
Speed Setting Methods Set 1 method from the following.
- Internal Speed Potentiometer (1 pc)
- External Speed Potentiometer (20kΩ 1/4W)
- DC Voltage Control (0~5 VDC)
Input Signals Photocoupler Input Method, Input Resistance 2.3kΩ, Operates with Internal Power Supply 12VDC
Common to CW/CCW, speed setting input selection, slow down, alarm reset
Output Signals Open-Collector Output Operated by External Power Supply Usage Conditions 26.4 VDC 10 mA max.
Speed Monitor Output (12P/R), Alarm Output
Protective Functions

When the following protective functions are activated,
the alarm signal is output OFF and the alarm LED (red) blinks
to stop the motor.

  • Overload Protection: When a load exceeding the rated torque is applied to the motor for 5 seconds min.
  • Overvoltage Protection: When the regenerative ability is exceeded in the winding down load operation
     
    When the voltage applied to the inverter exceeds 115 VAC or 230 VAC by about 30 % min.
  • Overcurrent Protection: When an excessive current flows inside the inverter
  • Undervoltage Protection: When the voltage applied to the inverter is
    about 15 % min. below 100 VAC or 200 VAC
  • Circuit Overheat Protection: When the temperature of the components inside the inverter exceeds the standard value
  • Motor Disconnection Protection: In case of motor cable disconnection or poor connection
    When the thermal protector built into the motor is activated
  • EEPROM Data Error: When an error is detected in EEPROM
Maximum Extension Distance 50 m between motor and inverter
Time Rating Continuous

General Specifications

Item Motor Inverter
Insulation Resistance After rated operation at normal ambient temperature and humidity, the measurement between the coils and the case is 100 MΩ min. using a 500 VDC megger. After rated operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply input terminal and the protective earth terminal, and between the power supply input terminal and the I/O signal terminal is min. 100 MΩ.
Dielectric Strength No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after rated operation at normal ambient temperature and humidity. After rated operation at normal ambient temperature and humidity, no abnormality is observed when 50 Hz or 60 Hz, 1.5 kVAC is applied between the power supply input terminal and the protective earth terminal for 1 minute, and 50 Hz or 60 Hz, 3 kVAC is applied between the power supply input terminal and the I/O terminal for 1 minute.
Temperature Rise After rated operation under normal ambient temperature and humidity, the winding temperature rise measured by the resistance change method with the gearhead or equivalent heat sink * attached to the motor is 70 °C max. −
Operating Temperature Range -10~+40°C (at 100 V and 200 V: -10~+50°C) (Non-freezing) 0∼+50°C (Non-freezing)
Operating Humidity Range 85 % max. (Non-condensing) 85 % max. (Non-condensing)
Thermal Class 130(B) -
Degree of Protection IP54 (Excluding mounting surface of the Round Shaft Type.) IP10
  • *Heat Sink Size: 230×230 mm, 5 mm thickness (Material: Aluminum)

Permissible Radial Load and Permissible Axial Load

Product Name Gear Ratio Permissible Radial Load Permissible Axial Load
N
10 mm From Shaft End
N		 20 mm From Shaft End
N
BHF62 ■T-□RH
BHF62 ■MT-□RH		 5~30 1200* 1100* 300
50~180 2200* 2000*
BHF62 ■T-□RA
BHF62 ■MT-□RA		 5~30 900 1000 300
50~180 1700 1850
BHF62 ■T-□
BHF62 ■MT-□		 3~30 550 800 200
50~180 650 1000
  • *For the hollow shaft type, the permissible radial load is the value at the distance from the mounting surface of the flange.
Radial Load and Axial Load

System Configuration

System Configuration

Cables and Accessories

Data Download
close