Induction Motors
5IK100VKEST-5H50S
Motor
This product is currently no longer available for sale.
| Product Classification | Product Name | List Price | Shipping Date |
|---|---|---|---|
| Motor | 5IK100VKEST-5H50S | - | Discontinued Product (31.3.2024 discontinued) |
Included
- Mounting Screws, Parallel Key (Stainless steel), Safety Cover, Operating Manual
Specifications
Data Download
Other Specifications
General Specifications
| Item | Specifications |
|---|---|
| Insulation Resistance | 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. |
| Dielectric Strength | No abnormality is observed when 1.5 kVAC at 50 Hz or 60 Hz applied between the coils and case for 1 minute after continuous operation under normal ambient temperature and humidity. |
| Temperature Rise | Winding temperature rise is a max. of 80 °C, measured by the resistance change method after rated load continuous operation under normal ambient temperature and humidity. |
| Thermal Class | 130 (B) |
| Operating Ambient Temperature | 0~+40 °C (Non-freezing) |
| Operating Ambient Humidity | 85 % max. (Non-condensing) |
| Degree of Protection | Terminal Box Type: IP66* |
Note
- No built-in overheat protection device (thermal protector).
When there is an overload or the output shaft is locked, use the electromagnetic switch and the inverter's electronic thermal function to prevent motor burnout.
- * The IP indication that shows the watertight and dust-resistant performance is specified under IEC60529 and IEC60034-5.
For materials and surface treatment, refer to the table below.
| Type | Output | Material/Surface Treatment | ||
|---|---|---|---|---|
| Point | Materials | Surface Treatment | ||
|
Right-angle hollow shaft hypoid JH Gearhead |
30 W 40 W 100 W |
Motor Case | Aluminum |
Painting (excluding installation surface) |
| Gear Case | ||||
| Terminal box | ||||
| Output shaft | Stainless Steel | - | ||
| Screw |
Stainless Steel (externally facing screws only) |
- | ||
Permissible Radial Load and Permissible Axial Load
| Gear Ratio | 10 | 15 | 20 | 30 | 50 | 100 | 200 | |
|---|---|---|---|---|---|---|---|---|
| Permissible Radial Load [N]*1 *2 | 10 mm From Mounting Surface | 415 | 554 | 692 | 923 | 1112 | 1196 | 1291 |
| 20 mm From Mounting Surface | 363 | 484 | 605 | 806 | 971 | 1045 | 1127 | |
| Permissible Axial Load [N] | 108 | 147 | 186 | 245 | 294 | 324 | 343 | |
- *1
- The load position is shown below.
- *2
- For calculations of the radial load from every distance for the hollow shaft type, refer to "Permissible radial load calculation for hollow shaft type" below.
Calculating the Permissible Radial Load for Hollow Shaft Type
The formula for calculating the permissible radial load varies depending on the mechanism.
Recommended Electromagnetic Switch
Always connect an electromagnetic switch when connecting the motor power supply.
Use an electromagnetic switch from the following product list, or an equivalent.
Set the rated current of the motor for the stabilized current of the thermal relay.
For the rated current of the motor, check the specifications for each product.
Fuji Electric FA Components & Systems Co., Ltd.
| Product Name | Part Number | |
|---|---|---|
| Parallel Shaft Combination Type, Round Shaft Type |
Right-Angle Hollow Shaft Hypoid Gearhead | |
|
4IK30
5IK40 |
4IK30VKJS, 4IK30VKES
5IK40VKJS, 5IK40VKES |
SC11AAN-□10TD |
| 5IK60 | - | SC11AAN-□10TF |
| 5IK100 | 5IK100VKJS | SC11AAN-□10TH |
| - | 5IK100VKES | SC11AAN-□10TG |
| 7IK200 Voltage 200-240 VAC | 7IK200 Voltage 200-240 VAC | SS11AAN-□10TK |
| 7IK200 Voltage 380-415 VAC | 7IK200 Voltage 380-415 VAC | SS11AAN-□10TH |
- *A letter indicating the winding code is specified where the box □ is located in the part number.
Use a product with the winding code that corresponds with the rated voltage of the motor.
| Rated Voltage | Winding Code | |
|---|---|---|
| 50 Hz | 60 Hz | |
| 200 VAC | 200-220 VAC | 2 |
| 200-220 VAC | 220-240 VAC | M |
| 220-240 VAC | 240-260 VAC | P |
| 346-380 VAC | 380-420 VAC | S |
| 380-400 VAC | 400-440 VAC | 4 |
| 415-440 VAC | 440-480 VAC | T |
Manufactured by Mitsubishi Electric Corporation
| Product Name | Part Number | |
|---|---|---|
| Parallel Shaft Combination Type, Round Shaft Type |
Right-Angle Hollow Shaft Hypoid Gearhead | |
|
4IK30
5IK40 |
4IK30VKJS, 4IK30VKES
5IK40VKJS, 5IK40VKES |
MSO-T10 0.24A 200V AC200 VAC |
| 5IK60 | - | MSO-T10 0.35 A 200 V AC200 VAC |
| 5IK100 | 5IK100VKJS, 5IK100VKES | MSO-T10 0.5 A 200 V AC200 VAC |
| 7IK200 Voltage 200-240 VAC | 7IK200 Voltage 200-240 VAC | MSO-T10 0.9 A 200 V AC200 VAC |
| 7IK200 Voltage 380-415 VAC | 7IK200 Voltage 380-415 VAC | MSO-T10 0.5 A 400 V AC400 VAC |
Usage with Inverter
When using in combination with an inverter, the setting frequency conditions of the inverter are as follows.
Refer to the operating manual for motor settings and precautions.
| Type | Product Name | Frequency |
|---|---|---|
| Right-Angle Hollow Shaft Hypoid Gearhead | 4IK30 | 100 Hz max. |
| 5IK40 | 80 Hz max. (60 Hz max. for gear ratio 10) | |
|
5IK100 7IK200 |
120 Hz max. | |
| Parallel Shaft Gearhead GV Gearhead Round Shaft Type |
4IK30
5IK40 5IK60 5IK100 7IK200 |
120 Hz max. |
System Configuration
Cables and Accessories
close