Brushless Motors BLU Series

BLU440S-5

BLU440S-5

Gearhead / Motor / Control Circuit

This product is currently no longer available for sale.

Product Classification	Product Name	List Price	Shipping Date
Gearhead / Motor / Control Circuit	BLU440S-5	-	Discontinued Product (1.4.2015 discontinued)

Included

Motor, Control Circuit, Gearhead, Power Supply Cable, Mounting Screw for Circuit, Short Bar, Mounting Screws, Parallel Key, Operating Manual

Specifications

Data Download

Other Specifications

Common Specifications

Item	Specifications
Speed Setting Methods	Speed potentiometer on front panel
Acceleration Time and Deceleration Time	0.5~10 sec: 2000 r/min at no load (However, this may vary depending on the size of the load.) Common settings are made using the acceleration time and deceleration time potentiometers on the back of the front panel.
Input Signals	Photocoupler Input Method (reinforced insulation photocoupler) Input Resistance 2.4kΩ Internal Power Supply Voltage 14 VDC±10% Operated by internal power supply Common to CW Input and CCW Input Sync Logic/Source Logic Selection... Switchable by Selection Switch: Factory settings Sink logic
Output Signals	Open-collector output (reinforced insulation photocoupler) Operated by external power supply Operating conditions 4.5~26.4 VDC 0.5~10 mA Common to Alarm Output and Speed Output
Protective Functions^*	When the following protective functions are activated, the motor will coast to a stop, and the ALARM output will be turned off. When the overload protective function is activated, the alarm LED of the driver will be blinking. It will light up when other protective functions are activated. Overload Protective Function: When a load exceeding the rated torque is applied to the motor for min. about 5 seconds Overvoltage Protective Function: When the application of power supply voltage to the driver exceeds 115 VAC or 230 VAC by 20 % min. When gravitational operation or driving a load exceeding the permissible load inertia is performed. Motor Sensor Error: When the sensor wire in the motor cable is broken Undervoltage Protective Function: When the application of power supply voltage to the driver exceeds 100 VAC or 200 VAC by 20 % min. Overspeed Protective Function: When the rotation speed of the motor reaches a speed of abnormality exceeding 2500 r/min
Maximum Extension Distance	Between motor and driver 10.5m (when an accessory connection cable is used)
Time Rating	Continuous

*The BLU series cannot control the speed control of the motor in applications where the motor side is turned from the load side, such as gravitational operation.
When a load exceeding the permissible load inertia value is driven, or when gravitational operation is performed, the overvoltage protective function works to bring the motor to a coasting stop.

General Specifications

Item		Motor	Driver
Insulation Resistance		100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity.	After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply terminal and the protective earth terminal, and between the power supply terminal and the I/O signal terminal is 100 MΩ min.
Dielectric Strength		No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity.	No abnormality is observed even with an application of 1.8 kVAC at 50 Hz between the power supply terminal and the protective earth terminal or 3 kVAC at 50 Hz between the power supply terminal and the signal I/O terminal for 1 minute after continuous operation at normal ambient temperature and humidity.
Temperature Rise		After continuous operation at normal ambient temperature and humidity, the temperature rise of the coil measured by the thermocouple method is 60 °C max. and that of the case surface is 50 °C max^*1.	−
Operating Environment	Ambient Temperature	UL, CSA Standards 0~+40°C (Non-freezing) EN Standards 0~+50°C (Non-freezing)	0~+40°C (Non-freezing)
	Ambient Humidity	85 % max. (Non-condensing)
	Altitude	Up to 1000 m above sea level
	Atmosphere	Cannot be used in special environments such as corrosive gas, no dust, radioactive materials, magnetic fields, or vacuums
	Vibration	Not subject to continuous vibration or excessive shock In conformance with JIS C 60068-2-6, "Sine-wave vibration test method" Frequency Range: 10~55 Hz, Half Amplitude: 0.15 mm, Sweep Direction: 3 directions (X, Y, Z), Number of Sweeps: 20 times
Storage Conditions^*2	Ambient Temperature	-25~+70°C (Non-freezing)
	Ambient Humidity	85 % max. (Non-condensing)
	Altitude	Up to 3000 m above sea level
Thermal Class		UL/CSA Standards: 105 (A), EN Standards: 120 (E)	−
Degree of Protection		IP65 (Excluding the installation surface of the round shaft type and connectors)	IP10

*1: Attach round shaft types to a heat sink (Material: aluminum) of one of the following sizes to maintain a motor case surface temperature of 90 °C max.
25 W Type: 135x135 mm, 5 mm thickness
40 W Type: 165x165 mm, 5 mm thickness
90 W Type: 200x200 mm, 5 mm thickness
*2: The value for storage condition applies to short periods such as the period during transport.

Note

Do not measure insulation resistance or perform a dielectric strength while the motor and driver are connected.

Permissible Radial Load and Permissible Axial Load

Combination type with a parallel shaft gearhead

Product Name	Gear Ratio	Permissible Radial Load		Permissible Axial Load N
Product Name	Gear Ratio	10 mm From Shaft End N	20 mm From Shaft End N	Permissible Axial Load N
BLU220■-□	5	100	150	40
	10, 15, 20	150	200
	30, 50, 100, 200	200	300
BLU440■-□	5	200	250	100
	10, 15, 20	300	350
	30, 50, 100, 200	450	550
BLU590■-□	5	300	400	150
	10, 15, 20	400	500
	30, 50, 100, 200	500	650

Radial Load and Axial Load

Combination type with a hollow shaft flat gearhead

Product Name	Gear Ratio	Permissible Radial Load		Permissible Axial Load N
Product Name	Gear Ratio	10 mm From the Gearhead Mounting Surface N	20 mm From the Gearhead Mounting Surface N	Permissible Axial Load N
BLU220■-□FR	5, 10	450	370	200
BLU220■-□FR	15, 20, 30, 50, 100, 200	500	400	200
BLU440■-□FR	5, 10	800	660	400
BLU440■-□FR	15, 20, 30, 50, 100, 200	1200	1000	400
BLU590■-□FR	5, 10	900	770	500
	15, 20	1300	1110
	30, 50, 100, 200	1500	1280

Radial Load and Axial Load

Round Shaft Type

Product Name	Permissible Radial Load		Permissible Axial Load
Product Name	10 mm From Shaft End N	20 mm From Shaft End N	Permissible Axial Load
BLU220■-A	70	100	Half of the motor mass or less
BLU440■-A	120	140
BLU590■-A	160	170

System Configuration

System Configuration

Cables and Accessories

Data Download

Specifications
Data Download
Other Specifications
System Configuration
Cables and Accessories