Brushless Motors BMU Series
BMU5200C-AC-2
Motor/Control Circuit
This product is currently no longer available for sale.
| Product Classification | Product Name | List Price | Shipping Date |
|---|---|---|---|
| Motor / Control Circuit | BMU5200C-AC-2 | - | Discontinued Product (31.3.2019 discontinued) |
Included
- Motor, Control Circuit, Connection Cable (2 m), CN1 connector, CN4 connector
Specifications
Characteristics
Dimensions
Data Download
Other Specifications
Common Specifications
| Item | Specifications |
|---|---|
| Speed Setting Methods | Digital Setting with Dial 4 speed settings |
| Acceleration Time and Deceleration Time |
Analog Setting:
0.5~15 Seconds: (Time from stop to rated speed)
Common setting for acceleration/deceleration time with acceleration/deceleration time potentiometer* Digital Setting:
0.0~15.0 s (set time from current speed to setting speed)
Acceleration time and deceleration time can be set individually for each operation data.*
|
| Input Signals |
Photocoupler Input Input resistance: 6.6 kΩ |
| Arbitrary signal assignment to IN0∼IN4 input (5 points) is possible. [ ]: Initial setting [FWD], [REV], [M0], [M1], [ALARM-RESET], EXT-ERROR, H-FREE |
|
| Output Signals | Photocoupler and Open-Collector Output External Power Supply: 4.5∼30 VDC 100 mA max. Sink output/source output Supported through external wiring |
| Arbitrary signal assignment to OUT0, OUT1 output (2 points) is possible. [ ]: Initial setting [ALARM-OUT1], [SPEED-OUT], ALARM-OUT2, MOVE, VA, WNG |
|
| Protective Functions | When the following protective functions are activated, ALARM-OUT1 output turns OFF, and the motor will come to a coasting stop. The alarm code will be displayed at the same time. (Instantaneous stop for external stop only) Overcurrent, main circuit overheat, overvoltage, undervoltage, sensor error, overload, over-speed, EEPROM error, Sensor error at power-on, prevention of operation at power-on, external stop |
| Maximum Extension Distance |
Standard Type (IP40 rating):
Motor and driver distance 10.5 m (when an accessory connection cable is used)
IP65 Rating:
Motor and driver distance 10.5 m (when an accessory connection cable is used)
|
| Time Rating | Continuous |
Overload Alarm Detection Time
The overload alarm is generated if the operation goes beyond the continuous duty region.
The detection time for this overload alarm can be set from 0.1~60.0 seconds arbitrarily. (Initial value: 30.0 seconds)
However, an alarm is generated for a max. length of 5 seconds in the following cases.
- If an applied load goes beyond the limited duty region
- If the output shaft is locked
General Specifications
| Item | Motor | Driver | |
|---|---|---|---|
| Insulation Resistance | 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. |
After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply terminal and the protective earth terminal, and between the power supply terminal and the I/O signal terminal is 100 MΩ min. |
|
| Dielectric Strength | No abnormality is observed when 1.5 kVAC at 50 Hz applied between the coils and case for 1 minute after continuous operation under normal ambient temperature and humidity. |
After continuous operation at normal ambient temperature and humidity, no abnormality is observed even if 50 Hz, 1.5 kVAC is applied between the power supply terminal and the protective earth terminal, and 50 Hz, 1.5 kVAC is applied between the power supply terminal and the I/O signal terminal for 1 minute. |
|
| Temperature Rise | After rated continuous operation at normal ambient temperature and humidity, the temperature rise of the coil measured value by the thermocouple method is max. 50 °C (max. 60 °C for 400 W), and the measured value of the temperature rise of the case surface is max. 40 °C (max. 50 °C for 400 W) *1. |
After continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method. |
|
| Operating Environment | Ambient Temperature | 0~+40°C (Non-freezing) | 0~+40°C (Non-freezing) 0~+40°C (Non-freezing) [0~+35 °C (non-freezing) only when the front side of the 400 W type driver is installed facing upward. The front side of the driver is the side with the display and setting dials.] |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Up to 1000 m above sea level | ||
| Atmosphere | No corrosive gases or dust Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. | ||
| Vibration | Not subject to continuous vibration or excessive shock In conformance with JIS C 60068-2-6, "Sine-wave vibration test method" Frequency Range: 10~55 Hz, Half Amplitude: 0.15 mm, Sweep Direction: 3 directions (X, Y, Z), Number of Sweeps: 20 times |
||
| Storage Conditions*2 | Ambient Temperature | -20~+70°C (Non-freezing) | -20~+70°C (Non-freezing) |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Up to 3000 m above sea level | ||
| Thermal Class | Standard Type (IP40 rating), IP65 Rating: UL/CSA Standards 105 (A), EN Standards 120 (E) | − | |
| Degree of Protection *3 |
Standard Type (IP40 rating):
IP40
IP65 Rating:
IP65 (Excluding the installation surface of the round shaft type and connectors)
|
IP20 | |
- *1
- Attach round shaft types to a heat sink (Material: aluminum) of one of the following sizes to maintain a motor case surface temperature of 90 °C max.
30 W Type: 115×115 mm, 5 mm thickness, 60 W Type: 135×135 mm, 5 mm thickness, 120 W Type: 165×165 mm, 5 mm thickness,
200 W Type: 200×200 mm, 5 mm thickness, 400 W Type: 250×250 mm, 6 mm thickness - *2
- The value for storage condition applies to short periods such as the period during transport.
- *3
- The IP indication that shows the watertight and dust-resistant performance are specified under IEC 60529 and IEC 60034-5.
Note
- Do not measure insulation resistance or perform a dielectric strength test the motor and driver are connected.
Motor Material and Surface Treatment
Materials
Case: Aluminum
Output Shaft: Standard Type (IP40 rating), IP65 Rating: S45C
Screw: Stainless Steel (externally exposed parts only. protective earth terminal excluded)
Output Shaft: Standard Type (IP40 rating), IP65 Rating: S45C
Screw: Stainless Steel (externally exposed parts only. protective earth terminal excluded)
Surface Treatment
Case: Painted (except for mounting surface)
System Configuration
Cables and Accessories
close
close
close
close