DiMER

AIP5150CB-P25

This product is currently no longer available for sale.

Product Classification	Product Name	List Price	Shipping Date
Geared Motor / Control Circuit	AIP5150CB-P25	-	Discontinued Product (1.4.2013 discontinued)

Actuator, Control Circuit, Parallel Key, Control I/O Connector, Operating Manual

Specifications

Control Method	Sinusoidal PWM method
Speed and Positioning Control Command	Pulse Input
Maximum Input Pulse Frequency	1000 Pulse/Setting: 50 kHz
Maximum Input Pulse Frequency	500 Pulse/Setting: 25 kHz
Protective Function	When the following protective functions are activated, an alarm signal will output, and the motor will come to a coasting stop. Overheat protection, overload protection, overvoltage protection, speed error protection, motor disconnection protection
Input Signals	Photocoupler Input Input resistance: 220 Ω Input current 7~20 mA (clockwise pulse, reverse pulse, hold-off, counter clear)
Output Signals	Photocoupler and open-collector output, external use conditions 5~30 VDC max., 15 mA max. (positioning completion, alarm, timing, feedback pulses phase A and B) Line driver output equivalent to 26C31 (feedback pulse phase A and B)

Values are after rated operation at normal ambient temperature and humidity.

Classification		Motor	Driver
Insulation Class		Class B (130 °C) [UL/CSA is approved to Class A (105 °C)].	-
Insulation Resistance		Value measured between the case and coil using a 500 VDC megger is 100 MΩ min.	100 MΩ or more when a 500 VDC megger is applied between the following places. Between case and power supply input terminal Between signal I/O terminal and power supply input terminal
Dielectric Strength		No abnormality was observed even when 1.5 kV at 50 Hz is applied between the case and coil for 1 minute.	Sufficient to withstand the following for 1 minute. Between case and power supply input terminal 1.25 kVAC (1.5 kVAC) at 50 Hz or 60 Hz Between signal I/O terminal and power supply input terminal 2.3 kVAC (3.0 kVAC) 50 Hz or 60 Hz ( ) Figures in parentheses indicate 200 V input
Operating Environment (When operating)	Ambient Temperature	0~+50 °C (Non-freezing): PL geared type , standard type 0~+40 °C (Non-freezing): Harmonic Geared Type	0∼+50 °C (Non-freezing)
	Ambient Humidity	85 % max. (Non-condensing)
	Atmosphere	No corrosive gases or dust. No exposure to water, oil or other liquids.
Shaft Runout		0.05 T.I.R. (mm)^*	-
Concentricity of Installation Pilot to the Shaft		0.075 T.I.R. (mm)^*	-
Perpendicularity of mounting surface to shaft		0.075 T.I.R. (mm)^*	-

*T.I.R. (Total Indicator Reading): The total dial gauge reading when the measurement section is rotated once around the reference axis center.

Note

Do not measure insulation resistance or perform a dielectric strength test while the motor and driver are connected.

Unit: N
Product Name	Permissible Radial Load		Permissible Axial Load
	Distance from Shaft End
	10 mm	20 mm
AIP030-□■	57	75	Use half of self-weight of motor as a reference.
AIP275-□■	112	134
AIP4150-□■	165	192
AIP275□■-P5	150	190	50
AIP275□■-P7.2	200	250
AIP275□■-P10	250	320
AIP275□■-P25	300	380
AIP275□■-P36	350	450
AIP275□■-P50	400	510
AIP5150□■-P5	450	590	200
AIP5150□■-P7.2	550	720
AIP5150□■-P10	600	790
AIP5150□■-P25	850	1120
AIP5150□■-P36	950	1250
AIP5150□■-P50	1050	1380
AIP030□■-H50	230	350	200
AIP030□■-H100	230	350	200
AIP275□■-H50	370	480	400
AIP275□■-H100	370	480	400
AIP5150□■-H50	1230	1410	1300
AIP5150□■-H100	1230	1410	1300

Either A or C indicating the power supply input is specified where the box □ is located in the product name.
A2, A, B2, B, or M indicating the shape is specified where the box ■ is located in the product name.